# How Many Tiles Do You Need?

_Published October 27, 2026_

**In short:** Divide 144 by the tile plus joint area to get tiles per square foot, multiply by the floor area and add waste. A 10x8 foot floor in 12x12 inch tile with a 1/8 inch joint takes 0.98 tiles per square foot, so 87 tiles with 10 percent extra. Daltile recommends buying about 10 percent more tile than you expect to need.

## Tiles per square foot comes first

Tile is counted in pieces. To get the number you need, work out how many tiles cover a square foot, which depends on the tile size and the grout joint, multiply by the area, and add waste. Each tile effectively covers its own face plus one grout joint.

```
tiles per sq ft = 144 / ((tile width + joint) x (tile length + joint))
order = area x tiles per sq ft x (1 + waste)
```

The [tile calculator](../../tile-calculator/) follows this formula. For 12 x 12 inch tile with a 1/8 inch joint, one tile covers about 1.02 square feet, so it takes 0.98 tiles per square foot.

## Worked example: a 10 x 8 foot floor

The floor is 80 square feet. With 12 x 12 inch tiles, a 1/8 inch joint and 10 percent waste, you need 87 tiles, which is 8 boxes at 11 tiles per box. A diagonal layout at 15 percent takes 91 tiles.

## How much extra tile

Daltile says it highly recommends purchasing approximately 10 percent more tile than you anticipate needing. That extra is also your "attic stock": tile from the same dye lot and printing process, which can change slightly over the years, for repairs or an expansion. The calculator offers 7 percent for a straight grid, 10 percent for a layout with many cuts, 15 percent for diagonal and 20 percent for herringbone or pattern work, and the higher figures reflect the extra cuts at walls and corners.

| Layout | Waste | Tiles to buy | Boxes of 11 |
| --- | --- | --- | --- |
| Straight grid | 7% | 84 | 8 |
| Straight, with many cuts | 10% | 87 | 8 |
| Diagonal | 15% | 91 | 9 |
| Herringbone or pattern | 20% | 95 | 9 |

## Tile count by tile size

The same 80 square foot floor takes very different numbers of tiles depending on the size, using a 1/8 inch joint and 10 percent waste:

| Tile size | Tiles per sq ft | Tiles to buy |
| --- | --- | --- |
| 4 x 4 in | 8.46 | 745 |
| 6 x 6 in | 3.84 | 338 |
| 12 x 12 in | 0.98 | 87 |
| 12 x 24 in | 0.49 | 44 |
| 24 x 24 in | 0.25 | 22 |

Large tiles mean fewer pieces but bigger cuts at the walls, so check whether the wastage for your room is closer to 10 percent or more. Always count in the tile size you actually plan to buy.

## Small tile and wider joints

Smaller tile means many more pieces. The same 10 x 8 foot floor in 4 x 4 inch tile is 8.46 tiles per square foot, and with 10 percent waste it takes 745 tiles. A wider joint spreads the tiles out: with a 1/4 inch joint on the 12 inch tile, the order with 10 percent waste is 85, compared with 87 at 1/8 inch.

## Plan the layout before you order

The Marazzi installation guide from Daltile starts with layout. Mark the center point of all four walls, snap chalk lines between them, and lay a row of loose tiles along the center lines with spacers. If that layout leaves cuts smaller than half a tile at the walls, move the center line half a tile toward the wall. Doing a dry layout shows how many cuts you will make, and it helps you pick the waste figure.

## Check the box before you buy

Read the dimensions printed on the carton, since they can differ from the name of the tile. Enter the actual dimensions into the calculator, along with the number of tiles per box, and check that all the boxes carry the same lot number. If the joint you want differs from the default, change it too, because even a small change in joint width alters the count on a large floor.

## Setting materials

The calculator also gives a rough setting-material list: about 6.6 pounds of grout for this floor and 1 bag of thinset, assuming one 50 pound bag covers about 80 square feet with a 1/4 x 3/8 inch notched trowel. Those are planning figures. The coverage depends on the trowel and the tile, so check the bag and the manufacturer's instructions.

## Common mistakes

- **Ignoring the grout joint.** It changes the count.

- **Using the same waste for every pattern.** Diagonal and herringbone need more.

- **Not rounding up to boxes.** Tile comes in full boxes.

- **Buying a second lot later.** The color and size can shift between lots.

- **Skipping the dry layout.** It shows the cuts you cannot avoid.

## What else to order

Add spacers, backer board or underlayment where needed, a notched trowel, sealer for natural stone and trim pieces. Use the [square footage calculator](../../square-footage-calculator/) for the area of irregular rooms.

## Frequently asked questions

### How many 12x12 tiles do I need for a 10x8 floor?

The floor is 80 square feet. With a 1/8 inch joint and 10 percent waste you need 87 tiles, or 8 boxes of 11.

### How much extra tile should I buy?

Daltile says it highly recommends buying approximately 10 percent more tile than you anticipate needing, and more for diagonal or herringbone layouts that need extra cuts.

### Why buy extra tile from the same lot?

Daltile notes that dye lots and printing can change slightly over the years, so extra tile bought with the original order gives you a closer match for repairs.

## Sources and further reading

- [Tile & Stone FAQs](https://www.daltile.com/how-to/faqs) — Daltile
- [Step-by-Step Floor Tile Installation](https://digitalassets.daltile.com/content/dam/Marazzi/website/documents/content/MZ_Installing_Tile_web.pdf) — Marazzi (Daltile)
