# How Much Paint Do You Need for a House Exterior?

_Published October 22, 2026_

**In short:** Multiply the house perimeter by the wall height, add the gables, subtract doors and windows, then divide by coverage of 250 to 400 square feet per gallon. A 40x30 foot one-story house has about 1,268 square feet to paint, which is roughly 8.5 gallons for two coats at 300 square feet per gallon.

## The area comes from the walls and the gables

Estimating exterior paint uses the same division as a room: area divided by coverage. The only new part is measuring a house. Multiply the perimeter by the wall height to get the body, then add the triangles of the gable ends, and subtract windows and doors. The [siding calculator](../../siding-calculator/) uses the same wall-area method.

```
wall area = perimeter x height + gables - doors - windows
gallons = wall area x coats / coverage per gallon
```

A gable is a triangle, so its area is half the base times the height. A gable 20 feet wide and 10 feet tall has 100 square feet, and a house with a gable at each end has twice that.

## Worked example: a 40 x 30 foot one-story house

The perimeter is 140 feet, and with 9 foot walls the body is 1,260 square feet. Add 200 square feet of gables, which gives 1,460 square feet of gross wall. Subtract two doors and ten windows, at the siding calculator's 21 and 15 square feet each, and the paintable area is 1,268 square feet. A garage door of 112 square feet would take it down to 1,156.

## How many gallons?

Coverage for exterior paint is lower than the label's best case. Sherwin-Williams says a gallon generally covers 250 to 400 square feet for exterior work, and recommends two coats. Glidden says up to 400 square feet on primed, smooth, non-porous surfaces, and that porous surfaces may need more than one coat. The table shows the example house at three coverage rates.

| Coverage | One coat (gal) | Two coats (gal) |
| --- | --- | --- |
| 250 sq ft per gallon | 5.1 | 10.1 |
| 300 sq ft per gallon | 4.2 | 8.5 |
| 400 sq ft per gallon | 3.2 | 6.3 |

For a house with rough siding, stucco or bare wood, the low end of the range is the safer figure, and two coats at 300 square feet per gallon comes to 8.5 gallons, which means buying 9. On smooth, primed siding at the top of the range the same job is 6.3 gallons.

## Trim, doors and primer

Siding takes most of the paint, but trim, fascia, doors and shutters are extra, and they are often painted in a different color and sheen. Estimate them by measuring their length and width, and plan a separate quart or gallon. Bare wood, patched areas and big color changes call for primer. Sherwin-Williams says a gallon of primer covers about 200 to 300 square feet, so it goes less far than topcoat.

## Texture and condition

Sherwin-Williams' FAQ says its 400 square foot figure is theoretical, because the texture of the surface and the paint left on tools are not part of the calculation. Rough siding, brick and stucco soak up more paint than smooth boards. Glidden's note that porous surfaces may need more than one coat points the same way. If you are unsure, test a small area and see how far a measured quantity goes.

## A rule of thumb per square of siding

Siding is counted in squares of 100 square feet, and paint can be scaled the same way. At 300 square feet per gallon, a square needs a third of a gallon per coat, or about two thirds of a gallon for two coats. The example house has 12.7 squares of paintable wall, so two coats at 300 square feet per gallon come to about 8.5 gallons, the same answer as the table. Use whichever way of counting you trust, round up, and remember to compare your result with the coverage printed on the can you actually buy.

## Common mistakes

- **Leaving out the gables.** They add a lot of area on a house with steep roofs.

- **Using the best-case coverage.** Use 250 to 300 for textured surfaces.

- **Not subtracting openings.** Windows and doors are not paint.

- **Counting one coat.** A color change or bare surface needs two or more.

- **Forgetting trim.** It is a separate product and a separate order.

## What else to buy

Add primer, caulk, scrapers, ladders or scaffolding rental, and paint for trim and doors. A surface that needs repair before painting changes the plan, so fix it first. If you are re-siding instead, count squares of siding with the siding calculator, and treat all quantities here as planning estimates.

## Frequently asked questions

### How many gallons of paint do I need for the outside of a house?

It depends on the wall area. A 40x30 foot one-story house with 9 foot walls, gables, two doors and ten windows has about 1,268 square feet, which takes about 8.5 gallons for two coats at 300 square feet per gallon.

### How much exterior paint does a gallon cover?

Sherwin-Williams says generally 250 to 400 square feet per gallon for exterior paint. Glidden says up to 400 on primed, smooth, non-porous surfaces. Rough surfaces fall toward the low end.

### How do I measure a house for paint?

Multiply the house perimeter by the wall height, add each gable (half the base times the height), and subtract windows and doors.

## Sources and further reading

- [How to Paint a House Exterior](https://www.sherwin-williams.com/en-us/project-center/paint/exterior-painting-how-tos) — Sherwin-Williams
- [Paint Selection Frequently Asked Questions](https://www.sherwin-williams.com/homeowners/how-to/painting-and-staining-faqs/painting-selection-faqs) — Sherwin-Williams
- [Paint Calculator](https://www.glidden.com/paint-calculator) — Glidden
