How Much Grass Seed Do You Need for a Lawn?
Seed is applied by the pound per 1,000 square feet, and the rate depends on the grass. A 2,000 sq ft lawn (50x40 ft) of tall fescue needs about 16 pounds for a new lawn at 8 lb per 1,000 sq ft, or 4 bags of 5 lb, and about 8 pounds to overseed. Follow the rate on your seed bag.
Seeding rates come in pounds per 1,000 square feet
Seed is bought by the pound, but recommended in pounds per 1,000 square feet, and the rate depends on the grass. Extension publications give ranges because seed size, purity and germination differ. NMSU's turfgrass guide lists, per 1,000 square feet, 1 to 2 pounds of Kentucky bluegrass, 3 to 4 of fine fescue, and 7 to 9 each of perennial ryegrass and tall fescue. The University of Nebraska-Lincoln lists 2 to 3 pounds for Kentucky bluegrass seeded alone and 6 to 8 pounds for tall fescue seeded alone. Because the sources differ, the calculator uses a typical rate for each grass, and the label on your seed bag is the rate to follow.
Seed for a 2,000 square foot lawn
A lawn 50 feet by 40 feet is 2,000 square feet. These are new-lawn rates from the grass seed calculator, with 5 pound bags.
| Grass | Rate per 1,000 sq ft | Seed for 2,000 sq ft | 5 lb bags |
|---|---|---|---|
| Tall fescue | 8 lb | 16 lb | 4 |
| Kentucky bluegrass | 2.5 lb | 5 lb | 1 |
| Perennial ryegrass | 7 lb | 14 lb | 3 |
| Fine fescue | 4 lb | 8 lb | 2 |
Kentucky bluegrass needs far less seed by weight than tall fescue. For a single 1,000 square foot area the calculator gives 2.5 pounds of it, against 8 pounds of tall fescue.
Counting bags
Divide the pounds you need by the bag size and round up. A new tall fescue lawn of 2,000 square feet needs 16 pounds, which is 4 bags of 5 pounds. Buying whole bags leaves a little over, and it is worth having for patching bare spots later. If the label gives a different rate from the table, scale the answer: multiply the label rate by the lawn area in thousands of square feet.
Why the rate varies
NMSU explains that seeding rates vary with the species and are determined by seed size, purity, percent germination and growth habit. That is why a pound of one grass seed covers far more ground than a pound of another, and why a coated or blended seed can carry its own rate. Read the bag for the rate and for the percent germination before you buy.
Overseeding uses less
When you are thickening an existing lawn rather than starting from bare soil, the calculator uses about half the new-lawn rate. For the same 2,000 square foot lawn of tall fescue that is 8 pounds instead of 16. Seed labels often print an overseeding rate of their own, and that is the figure to use.
Apply it evenly
Both extension guides stress even coverage. NMSU says hand seeding suits small areas and a drop-type spreader is generally preferred for larger ones because wind affects its pattern less than a rotary spreader. UNL says to calibrate a drop seeder and then seed in two or three passes in different directions. After seeding, rake lightly and roll lightly, because good seed-to-soil contact matters most for quick germination. Do not bury the seed deep.
Straw and timing
UNL recommends one bale of clean, weed-free straw per 1,000 square feet to cover the seed, which gives a light cover that does not need to be removed after germination. That is 2 bales for a 2,000 square foot lawn, and the calculator counts bales the same way. Most people apply too much straw, which shades the seedlings. NMSU says cool-season grasses such as Kentucky bluegrass, perennial ryegrass and tall fescue are best established in late summer or early fall.
Prepare the soil first
Seed needs somewhere to root. NMSU's absolute minimum soil depth for a lawn is 4 inches, and UNL recommends 4 inches of topsoil over the subsoil. Size the topsoil with the topsoil calculator, and spread starter fertilizer based on a soil test.
Common mistakes
- Using one rate for every grass. Kentucky bluegrass and tall fescue differ by a factor of three or more.
- Ignoring the bag. Coated and blended seed has its own rate. Follow the label.
- Seeding too thickly. More seed does not make a better lawn, and seedlings compete.
- Burying the seed. It needs contact with the soil, not a deep covering.
- Using too much straw. A light cover is enough.
What else to order
Add starter fertilizer, straw, and a way to water the seeded area daily until the grass is up. Treat the quantities here as planning estimates.
Calculators for this guide
Frequently asked questions
How many pounds of grass seed per 1,000 square feet?
It depends on the grass. NMSU Extension lists 1 to 2 pounds for Kentucky bluegrass and 7 to 9 for tall fescue and perennial ryegrass. UNL Extension lists 2 to 3 pounds for bluegrass and 6 to 8 for tall fescue seeded alone.
How much seed do I need to overseed a lawn?
The calculator uses about half the new-lawn rate. For 2,000 square feet of tall fescue that is 8 pounds instead of 16. Check your seed label for its own overseeding rate.
How much straw do I need to cover grass seed?
UNL Extension recommends one bale of clean straw per 1,000 square feet, which is 2 bales for 2,000 square feet.
Sources and further reading
- Turfgrass Establishment (Guide H-509) — New Mexico State University Extension
- Establishing Lawns From Seed — University of Nebraska-Lincoln Extension
More guides
Estimates only. Always confirm quantities with your supplier or a qualified contractor before ordering, and add extra for waste and site conditions.