How Much Siding Do You Need for a House?

In short

Siding is sold by the square (100 square feet). Multiply the perimeter by the wall height, add the gables, subtract the openings, divide by 100 and add 5 to 10 percent for waste. A house with a 160 foot perimeter, 9 foot walls and 200 square feet of gables has 1,448 square feet of net siding, or 16.0 squares with 10 percent waste.

Siding is sold by the square

In the siding trade, one square is 100 square feet of wall. LP's measuring guide lays out the method: measure each wall, add the gables and dormers, subtract the openings you will not cover, then divide the net square footage by 100 to get the number of squares to order. The siding calculator follows the same steps.

squares = (perimeter x height + gables - openings) x (1 + waste) / 100

Step 1: the walls

For a house with a 160 foot perimeter and 9 foot walls, the walls are 160 x 9 = 1,440 square feet. CertainTeed's estimating guide measures each rectangular wall's height excluding gables, and width including doors and windows, which means it counts the full wall and leaves the subtraction for later.

Step 2: the gables

A gable is a triangle: half the base times the height. CertainTeed adds 1 foot to the height of a gable measured at the center to allow for waste, and notes that lower pitch roofs produce more waste than higher pitch ones. In the example, the two gable ends come to 200 square feet, which brings the gross wall area to 1,640 square feet.

Step 3: the openings

Subtract windows and doors. LP's guide says to measure each one, and if you are unsure to use 15 square feet per window and 20 per door. The calculator uses 15 and 21. With two doors and ten windows, the net siding area is 1,448 square feet. A 112 square foot double garage door takes that down to 1,336. Subtracting openings gives a tighter number, but a few more pieces is safer if your measurements are rough.

Step 4: waste

LP suggests adding 5 to 10 percent for mistakes, repairs and starter strips. CertainTeed says to add 10 percent for large projects, for siding, soffit and accessories. The calculator uses 10 percent. For the example house the order is 16.0 squares with 10 percent waste, 15.3 with 5 percent, and 14.5 with none. With the garage door deducted and 10 percent waste, it is 14.7 squares.

Worked example

A one-story house with a 160 foot perimeter, 9 foot walls, 200 square feet of gables, two doors and ten windows has 1,640 square feet of gross wall and 1,448 square feet of net siding. Divide by 100 and add 10 percent, and you order 16.0 squares. A smaller house with a 120 foot perimeter, 100 square feet of gables, one door and six windows needs 11.8 squares.

From squares to pieces

Siding comes as panels or boards, and the exposure sets how much wall each covers. For the example house the number of pieces depends on the product:

ProductPieces to buy
Vinyl clapboard, 8 in exposure200
Fiber cement lap, 7.25 in exposure220
Wood lap, 8.3 in exposure192
Vinyl dutchlap, 10 in152

These counts come from the coverage per piece in the calculator, and the packaging tells you the real number of pieces per square. Always buy by the manufacturer's coverage.

Trim, corners and J-channel

LP says trim is measured in linear feet, not squares. The calculator estimates 4 outside corner posts of 10 feet for four corners and about 154 feet of J-channel or trim around the openings. Those are planning numbers, so count the real lengths on your plan.

A quick cost check

At the placeholder price of $220 per square, the material for the example house is about $3,520. Real prices vary widely by material, so enter your own, and add insulation or sheathing, housewrap, flashing, fasteners and labor.

Common mistakes

What else to order

Besides the siding itself, plan for starter strip, housewrap, flashing, soffit, fasteners and caulk. LP also recommends having a professional verify the final measurements before you place a large order. If you will paint the house afterward, use the paint calculator.

Calculators for this guide

Frequently asked questions

How many squares of siding do I need?

Add up the wall and gable areas, subtract openings, and divide by 100. The example house has 1,448 square feet of net siding, which is 14.5 squares, or 16.0 squares with 10 percent waste.

How much do I subtract for windows and doors?

LP's measuring guide says to measure each opening, and if unsure to use 15 square feet per window and 20 per door.

How much extra siding should I order?

LP suggests 5 to 10 percent for mistakes, repairs and starter strips, and CertainTeed says to add 10 percent for large projects.

Sources and further reading

More guides

Estimates only. Always confirm quantities with your supplier or a qualified contractor before ordering, and add extra for waste and site conditions.