How Much Material Do You Need for a Retaining Wall?
A 30 foot long, 3 foot high wall of 16x6 inch blocks with one buried course has 7 courses, 23 blocks per course, and needs about 138 wall blocks and 25 caps before waste. Add a 6 inch compacted base (1.2 cubic yards) and 3.9 cubic yards of drainage gravel behind the wall.
What a segmental retaining wall needs
A block retaining wall is more than a stack of blocks. The material list has four parts: the blocks and caps, a compacted base under the first course, drainage gravel behind the wall, and, in most designs, fabric between the gravel and the soil. The retaining wall calculator estimates all four from the wall length, height and block size.
Step 1: count the courses and the blocks
Divide the wall height by the block height to get the number of visible courses, then add the buried course. A 30 foot wall that is 3 feet high, built from 16 x 6 inch blocks with one buried course, has 7 courses in all. Each course is 30 feet divided by 16 inches, rounded up, which is 23 blocks, and the top row is made of cap blocks instead of wall blocks.
The calculator gives 138 wall blocks and 25 cap blocks before waste for this wall. With the default 8 percent allowance for cuts and breakage, the order becomes 150 wall blocks and 25 caps.
Blocks and gravel for common walls
All rows use 16 x 6 inch blocks, one buried course, a 12 inch gravel backfill width and no waste.
| Wall (L x H) | Courses | Wall blocks | Cap blocks | Drainage gravel (cu yd) |
|---|---|---|---|---|
| 20 x 2 ft | 5 | 60 | 16 | 1.9 |
| 30 x 3 ft | 7 | 138 | 25 | 3.9 |
| 40 x 3 ft | 7 | 180 | 32 | 5.2 |
| 50 x 3 ft | 7 | 228 | 40 | 6.5 |
Step 2: the base trench
The first course sits on a compacted base. Rochester Concrete Products' installation guide for its Vintage 6 wall says a typical trench is 2 feet wide and 14 inches deep to bury a full course of 8 inch block, and that the base material must be at least 6 inches thick. Its quantity method is the wall length times the base thickness times the base width, divided by 27 for cubic yards, plus 10 percent for inconsistencies in the trench and for compaction. For the 30 foot wall, a 6 inch base 2 feet wide comes to 1.2 cubic yards with that 10 percent included.
Step 3: drainage gravel behind the wall
Water that builds up behind a wall pushes on it, so every segmental wall needs free-draining gravel behind the blocks. The calculator sizes a strip 12 inches wide over the full height, which for the example wall is 3.9 cubic yards, or about 5.4 tons at 1.4 tons per cubic yard. The manufacturer's guide uses a slightly different method, with enough rock to fill 1 foot behind the tail of the block and to fill the block cores: wall face area in square feet times 1.50, divided by 27. For the 90 square feet of exposed face on this wall that is 5.0 cubic yards. If your blocks are hollow, plan on the larger figure and ask your supplier.
Step 4: fabric behind the gravel
Landscape fabric between the gravel and the soil keeps fine soil from clogging the drainage layer. The calculator allows for a strip as tall as the wall plus 2 feet, which is 150 square feet for the example wall. Follow the instructions for the block system you buy, because fabric details vary by manufacturer.
Check the rules before you dig
Taller walls are engineered structures. Montgomery County, Maryland's residential retaining wall guide, for example, requires a permit when the retained height is over 3 feet, or when the wall supports a surcharge load, crosses a lot line, sits in problem soils or is part of a tiered system. Other places set different limits, so ask your local building department before you build. The calculator's note says walls over 3 to 4 feet usually need engineering, geogrid reinforcement and a permit.
Common mistakes
- Forgetting the buried course. It counts toward the block order, and it is what stops the wall sliding out at the bottom.
- Skipping the compacted base. Blocks laid on loose soil settle unevenly.
- Using soil instead of drainage gravel behind the wall. Backfill with clean gravel, not the excavated dirt.
- Ordering no cap blocks. Caps are a separate item with their own count.
- Building tall without a plan. Over the local height limit, you need engineering and a permit.
What else to order
Besides the blocks, you need construction adhesive for the caps, a perforated drain pipe at the bottom of the gravel in many designs, and geogrid for taller walls. Size the gravel with the gravel calculator and follow the block maker's instructions for the full system.
Calculators for this guide
Frequently asked questions
How many blocks do I need for a 30 foot retaining wall that is 3 feet high?
With 16x6 inch blocks and one buried course, the wall is 7 courses of 23 blocks, which is 138 wall blocks and 25 cap blocks before waste. With 8 percent waste the order is 150 wall blocks and 25 caps.
How much gravel goes behind a retaining wall?
Manufacturers call for a drainage layer of free-draining rock behind the wall. The calculator uses a strip 12 inches wide over the full wall height, which is 3.9 cubic yards for a 30x3 foot wall. Rochester's guide uses a larger allowance, 1.50 times the face area divided by 27, to fill the block cores too.
Do I need a permit for a retaining wall?
It depends on where you live. Montgomery County, Maryland requires a permit for a retained height over 3 feet, and also for walls that carry extra load, cross a lot line or are tiered. Check with your local building department before you start.
Sources and further reading
- Installation Guide: Vintage 6 Freestanding/Retaining Walls — Rochester Concrete Products
- Residential Retaining Walls — Montgomery County Department of Permitting Services
More guides
Estimates only. Always confirm quantities with your supplier or a qualified contractor before ordering, and add extra for waste and site conditions.