How Much Does a Cubic Yard of Gravel Weigh?

In short

A cubic yard of gravel weighs roughly 2,500 to 2,800 pounds, or 1.25 to 1.4 tons. An extension weights bulletin lists crushed stone at 2,500 pounds and gravel at 2,700 per cubic yard, and the EPA lists loose gravel at about 2,565. Ten cubic yards weigh 12.5 to 14.0 tons. Moisture adds weight.

The short answer: about 1.3 to 1.4 tons per cubic yard

A cubic yard of gravel weighs roughly 2,500 to 2,800 pounds, or 1.25 to 1.4 tons. Published tables put loose gravel and crushed stone in that range. An extension bulletin on building material weights lists crushed stone at 2,500 pounds per cubic yard and gravel at 2,700, and the U.S. EPA's volume-to-weight table lists loose gravel at about 2,565 pounds per cubic yard and loose rock at about 2,570. The yards to tons calculator uses 1.4 tons as its default for gravel, which is toward the heavy end of that range.

tons = cubic yards x tons per cubic yard
cubic yards = tons / tons per cubic yard

What 10 cubic yards weigh

Ten cubic yards weigh 12.5 tons at 1.25 tons per yard, 13.5 tons at 1.35 and 14.0 tons at 1.4. The spread is about two tons on a ten-yard order, so the supplier's number matters when you are buying by the ton or checking what a truck can carry.

Different stone, different weight

The gravel calculator uses a planning density for each material, which you can see in the table. These are planning figures, not measurements, and the real weight of a load depends on the stone, its size and the moisture. The last column is the weight of 1 cubic yard (a 27 x 1 foot strip at a depth of 12 inches) from the calculator, in pounds.

MaterialTons per cubic yardPounds per cubic yardCalculator weight of 1 yd
Crushed stone / 3/4 in gravel1.402,8002,800
Pea gravel1.352,7002,700
River rock / washed stone1.302,6002,600
Road base / crusher run1.503,0003,000
Decomposed granite1.503,0003,000

The published tables do not split gravel into pea, crushed and road base, so treat the per-type figures as the calculator's assumptions and ask your supplier for the actual weight of what they sell.

Dry versus wet

Water adds weight without adding volume. The yards to tons calculator's note says that moisture, particle size and compaction change real weight, and that the densities are typical planning values. A load of gravel that has been rained on will weigh more than the same volume of dry stone, so a ticket may be heavier than your estimate.

Worked example: a driveway top-up

A driveway section 40 feet long, 12 feet wide and 4 inches deep is 5.9 cubic yards, and the gravel calculator gives 8.3 tons at its default density with no compaction allowance. At 1.35 tons per cubic yard the weight is a little lower, and at 1.4 it is a little higher. Add compaction and waste when you order, and ask whether the supplier sells by the ton or the yard.

Hauling gravel

Gravel is heavy, so vehicles reach their weight limit long before they fill up. If your vehicle's payload rating is 1,500 pounds, it can carry only 0.75 tons, which is 0.56 cubic yards of gravel at 1.35 tons per yard. A full ton is just 0.74 cubic yards. Check the payload rating in the owner's manual or on the door-jamb sticker, and remember that a pickup bed can hold more by volume than it can carry by weight. The cubic yard calculator treats a pickup as about one yard per load, but notes that heavy materials such as gravel limit the load by weight.

Weights for common order sizes

OrderTons at 1.25Tons at 1.4
1 cu yd1.21.4
2 cu yd2.52.8
5 cu yd6.27.0
10 cu yd12.514.0
20 cu yd25.028.0

From volume to weight in four steps

First, find the volume of the job in cubic yards with a calculator or the length x width x depth formula. Second, choose a density for gravel: use the supplier's figure if you can get it, and otherwise a planning value from the tables above. Third, multiply the cubic yards by tons per cubic yard. Fourth, compare the result with what your vehicle or trailer can legally and safely carry. For example, 8 cubic yards at 1.35 tons per yard comes to 10.8 tons.

Delivery tickets and scales

Many suppliers weigh the truck on a scale before and after loading, and the ticket shows the net tons. If you ordered by volume, ask how they convert, and compare the ticket with your estimate. A big gap is a reason to ask about moisture or to check that the load is the size you ordered.

Common mistakes

What else to consider

To work out how much gravel your project needs, use the gravel calculator, then convert with the yards to tons calculator. Treat the results as planning estimates and confirm with your supplier.

Calculators for this guide

Frequently asked questions

How many tons are in a cubic yard of gravel?

About 1.25 to 1.4. Published tables list crushed stone at 2,500 pounds, gravel at 2,700 and loose gravel at about 2,565 pounds per cubic yard. Ten cubic yards weigh 12.5 to 14.0 tons.

How much does a yard of pea gravel weigh?

The gravel calculator uses 1.35 tons per cubic yard for pea gravel, so ten yards weigh 13.5 tons. That is a planning figure, so ask the supplier.

How much gravel can a pickup truck carry?

By weight, not volume. A 1,500 pound payload is 0.75 tons, which is about 0.56 cubic yards at 1.35 tons per yard. Check your vehicle's payload rating.

Sources and further reading

More guides

Estimates only. Always confirm quantities with your supplier or a qualified contractor before ordering, and add extra for waste and site conditions.