Rebar Spacing for a Concrete Slab
Rebar spacing is set by your plans and local code, not by one rule. Patio and garage slabs commonly use grids of 12 to 18 inches. A 20x20 foot slab with #4 bar at 16 inches needs 16 bars each way, 704 feet with 10 percent waste, or 36 sticks of 20 feet. Keep the steel at or just above mid-depth.
There is no single required spacing
People often ask what rebar spacing a slab needs, and the honest answer is that it depends on the slab, the load, the soil and your local code. Concrete Network points out that for many slabs placed on well-compacted subbases, with control joints installed at the proper spacing, reinforcement is unnecessary, and that as a rule of thumb slabs thicker than 5 inches should get rebar or welded wire fabric, especially under heavy loads. When your plans or your local code call for steel, they will state the bar size and spacing, and those numbers are what you follow. This guide shows how to count the steel once you know them.
Common patio and garage slab grids
The rebar calculator notes that common patio and garage slabs use grids of 12 to 18 inches center to center, and it asks you to follow your plans or local code. That range is a planning default, not a rule. A closer grid means more steel, as the table shows for a 20 x 20 foot slab with #4 bar, 20 foot sticks and 10 percent for laps and cuts.
| Spacing | Bars each way | Total rebar | 20 ft sticks | Weight |
|---|---|---|---|---|
| 12 in | 21 | 924 ft | 47 | 617 lb |
| 16 in | 16 | 704 ft | 36 | 470 lb |
| 18 in | 14 | 616 ft | 31 | 411 lb |
| 24 in | 11 | 484 ft | 25 | 323 lb |
Worked example: a 20 x 20 foot slab at 16 inches
At 16 inches center to center, the grid has 16 bars in each direction, which is 640 feet of steel before waste. With 10 percent for laps and cuts the order is 704 feet, or 36 twenty-foot sticks weighing about 470 pounds. The calculator counts one layer of bars each way with the first bar at the slab edge, and notes that real jobs keep bars 2 to 3 inches inside the forms. At 12 inches the same slab needs 924 feet.
Bar size
Rebar sizes are numbered by their diameter in eighths of an inch, so #3 is 3/8 inch and #4 is 1/2 inch. Continental Steel's rebar listings show #3 at 0.376 pounds per foot and #4 at 0.668 pounds per foot. Concrete Network describes standard rebar as 1/2-inch steel rods in a lengthwise and crosswise grid near the center of the slab. Switching the example slab from #4 to #3 at 16 inches cuts the weight to 265 pounds, with the same 36 sticks. The bar size and spacing should come from your plans, because they are related.
Where the steel goes in the thickness
Concrete Network says the steel must be positioned at or just above the mid-depth of the slab to work well, and warns that misplaced steel can cause rebar shadowing and rust stains if it becomes exposed to moisture. A 4 inch slab is the minimum for a patio, according to Concrete Network's patio guide, which recommends 5 to 6 inches for heavy loads such as a hot tub or an outdoor fireplace. Support the bars on blocks or chairs so they stay at the right height as the concrete is placed, and tie the intersections so the grid does not shift.
Check before you pour
Before the truck arrives, walk the formwork with the plan in hand. Check that the grid is tied, that the bars are lifted off the base on chairs or blocks, that the ends clear the forms by the cover your plans call for, and that any inspection is booked. Steel that is wrong when the concrete goes in is very hard to fix later.
Mesh instead of rebar
Concrete Network describes wire mesh as often used as an alternative to rebar in residential slabs. It is cheaper mainly because the sheets go down faster than individual bars. Mesh has its own sheet sizes, wire gauges and overlaps, so check the product and the plan before you substitute.
Common mistakes
- Treating the calculator's range as code. Your plans and local rules decide the spacing.
- Leaving the steel on the ground. It should sit at or above mid-depth.
- Running bars to the edge. Keep them inside the forms.
- Forgetting laps. Where bars end, they overlap, and that uses extra length.
- Adding steel where it is not needed. A well-prepared slab with control joints may not need it.
What else to order
Plan on tie wire, chairs or blocks, and the concrete itself. Use the concrete calculator for the pour, and ask your building department what they require before you buy.
Calculators for this guide
Frequently asked questions
How far apart should rebar be in a concrete slab?
There is no one answer. The rebar calculator notes common patio and garage slabs use 12 to 18 inch grids, but your plans and local code decide. Concrete Network says many slabs on well-compacted subbases with proper control joints do not need reinforcement.
Where should rebar sit in a slab?
Concrete Network says the steel should be positioned at or just above the mid-depth of the slab, supported so it does not sink to the bottom.
How much rebar do I need for a 20x20 slab?
At 16 inch spacing with #4 bar, 16 bars each way: 640 feet before waste and 704 feet with 10 percent extra, or 36 sticks of 20 feet.
Sources and further reading
- Concrete Reinforcement in Slabs: Rebar, Wire or Fiber? — Concrete Network
- Reinforcing Bar No. 4 (0.668 lbs/ft) — Continental Steel
- Reinforcing Bar No. 3 (0.376 lbs/ft) — Continental Steel
- How Much Concrete Do I Need for a Patio? — Concrete Network
More guides
Estimates only. Always confirm quantities with your supplier or a qualified contractor before ordering, and add extra for waste and site conditions.