How Much Sand Do You Need for a Paver Patio?
A 12x12 ft paver patio needs about 12 cubic feet of bedding sand at a 1-inch layer. With 10 percent extra that is 13.2 cubic feet, 0.49 cubic yards or 26 bags of 50-lb sand. The thin bedding layer is small; the gravel base underneath is the big order.
The bedding layer is thin on purpose
Two different materials sit under a paver patio, and they are easy to mix up. The base is compacted gravel and does the structural work. The bedding is a thin layer of sand on top of it that you screed flat so every paver can seat evenly. Unilock's paver base guide says the bedding layer is typically 1 inch thick, and that is the number to build the order on.
One inch is not much. Spread over a 12x12 foot patio it comes to exactly 12 cubic feet, less than half a cubic yard. People who guess at the sand by feel tend to order far too much because they picture the patio's whole depth in sand instead of one inch of it.
The formula
cubic yards = cubic feet ÷ 27
bags = cubic feet of sand ÷ volume per bag
Then add extra for the sand you lose to uneven spots, to the screed rails and to the edges. The sand calculator adds 10 percent by default. Pick the paver bedding option in the project menu, because the calculator opens on the sandbox preset at 8 inches, and leaving it there would order eight times as much sand as a patio needs.
Sand by patio size
All rows use a 1-inch bedding layer, dry sand and 10 percent extra.
| Patio | Area | Sand | Cubic yards | 50-lb bags |
|---|---|---|---|---|
| 10 × 10 ft | 100 sq ft | 9.17 ft³ | 0.34 | 18 |
| 12 × 12 ft | 144 sq ft | 13.20 ft³ | 0.49 | 26 |
| 12 × 16 ft | 192 sq ft | 17.60 ft³ | 0.65 | 34 |
| 14 × 20 ft | 280 sq ft | 25.67 ft³ | 0.95 | 50 |
Notice that the sand grows in a straight line with area, while the gravel base grows with area and depth together. Doubling the patio doubles the sand; going from a 6-inch to a 10-inch base multiplies the gravel by about two thirds.
Worked example: a 12 x 12 patio
Take a 144 square foot patio. At 1 inch, the bedding sand is 12 cubic feet, or 0.44 cubic yards. Ten percent extra raises that to 13.2 cubic feet, which is 0.49 cubic yards and 26 bags of 50-lb sand. By weight the order is about 0.64 tons; the calculator assumes dry sand at roughly 1.3 tons per cubic yard, and damp sand weighs more, so a delivered load will tip the scale higher than the dry figure.
Fourteen by twenty feet is where the choice changes. At 50 bags it is nearly a full cubic yard, and hauling that many bags is a lot of lifting. Ask a local landscape supplier about a small bulk delivery, and compare it against the bags with the cubic yard calculator.
Which sand to buy
The sand type matters more than a few bags either way. The Concrete Masonry & Hardscapes Association's paving FAQ describes standard sand-set pavers as laid over a dense graded aggregate base with a concrete sand bedding, and its discussion of sand-set paving also refers to ASTM C144 mason sand, polymeric sand and ASTM C33 concrete sand. Which of those suits your paver and your joints is something the paver manufacturer's installation sheet settles, so read it before you order.
The same FAQ notes that joint sand should be monitored and topped up when the loss goes beyond one half inch. That joint sand is a separate, much smaller purchase from the bedding sand. The paver calculator estimates polymeric sand alongside the pavers and base.
Common mistakes
- Using the calculator's default depth. The sand calculator opens on the 8-inch sandbox preset. For a patio, switch it to the 1-inch paver bedding option.
- Making the bed thicker to fix a wavy base. Sand is meant to be a uniform thin layer. Fix low spots in the compacted gravel instead of filling them with sand.
- Counting the gravel as sand. The gravel base is a different, larger order and a different material.
- Ordering exactly the minimum. Edges, screed rails and spills all eat sand. Keep the 10 percent extra.
- Letting the bed get rained on. Wet sand is heavy and hard to screed flat, so cover the pile.
The gravel base is the bigger order
Since people usually come to this question while planning the whole patio, here is the other number. Unilock's chart gives patio base depths of 6 inches for sandy soil, 8 inches for silty soil and 10 inches for clay. It also says to spread and compact the gravel in lifts 3 inches thick. For the same 12x12 patio the gravel calculator gives 2.93 cubic yards at 6 inches, which is far more material than the sand. Check your local frost and drainage conditions, because those can change the base depth.
Calculators for this guide
Frequently asked questions
How much sand do I need for a 12x12 paver patio?
A 12x12 foot patio needs about 12 cubic feet of bedding sand at a 1-inch layer. With 10 percent extra that is 13.2 cubic feet, or 0.49 cubic yards, which is about 26 bags of 50-lb sand.
How thick should the sand under pavers be?
Unilock's paver base guide says the bedding layer is typically 1 inch thick. Keep it uniform and screeded flat, and fix low spots in the gravel base rather than adding sand.
Do I need sand or gravel under pavers?
Both. Compacted gravel forms the base, and a thin layer of sand on top of it, the bedding, lets you set the pavers level. The gravel is the larger order by volume.
Sources and further reading
- Paver Base Specifications — Unilock
- Pavement FAQ: sand-set pavers and bedding — Concrete Masonry & Hardscapes Association
More guides
Estimates only. Always confirm quantities with your supplier or a qualified contractor before ordering, and add extra for waste and site conditions.